Hid Magnetic Stripe Reader 644 Installation Guide Manuel d'utilisateur télécharger pdf

Specifications

INPUT;

Magnetic Stripe Cards, high or low coercivity, EMPI I, EMPI II or

ABA format.

CARD SIZE:

CR-80, 2.125" x 3.375" x .030", Track 1 or 2

(53.97mm x 85.73 mm x 0.762 mm)

CR-60, 2.328" x 3.250" x .030", Track 1 or 2

(59.13 mm x 82.55 mm x 0.762 mm)

OUTPUT:

Standard Wiegand 5-wire format with optional second LED

control line.

DISTANCE:

200 feet (61 m) with #22 AWG wire (0.325 mm)

500 feet (153 m) with #18 AWG wire (0.823 mm)

TEMPERATURE RANGE:

-31° to 150°F (-35° to +66°C)

POWER:

35 mA at 5 VDC

READ SPEED:

8 to 50 IPS in either direction.

DIMENSIONS:

Reader : 6.00" (L) x 1.35" (H) x 1.75" (W)

(152.4 mm x 34.29 mm x 44.45 mm)

Adapter Plate: 7.00" (L) x 2.75" (W)

(177.80 mm x 69.85 mm)

LED:

Two Colors - Red and Green

FCC Compliance Statement:

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

P/N: 2280-3961

REV B.2

4/20/04

Card Reader kit consists of:

1-Reader assembly

1-Installation Kit 2270-0018 or 2270-0611

1-Instructions 2280-3961

1-Instructions 2280-4189

(For Heater, Model 6446 or 6447)

General

The Model 644 Pass-Through Reader Card Reader reads

magnetic stripe cards that have been encoded with EMPI I or

EMPI II encrypted card numbering format or standard ABA

numbering format.

Cards are read in either direction and the information

transmitted to any host access controller that can supply a 5

VDC operating voltage to the reader, and that can accept the

standard Wiegand 26 or 34-bit format or Clock and Data format.

The card reading slot of the Model 644 Reader is set at an

angle to match the natural angle of the wrist when holding a

card. This angle must be considered when mounting the reader

for maximum user convenience.

The reader can be wall or door frame mounted, horizontal or

vertical, to suit the user.

The 644 card readers are weather resistant, although they

should be mounted to preclude ice build up. The 6446 and

6447 have a heater bar to help prevent ice build up.

The 644-S Custom Reader will have a prom that will read a

custom ABA format

Before Installing

1. Reader installation and wiring must conform to applicable

local codes, ordinances, and regulations.

2. The host controller must supply 5 VDC operating voltage

to the reader. The voltage as measured at the reader

must be between 3.2 to 5.5 VDC.

3. The maximum recommended reader distance from the

host is:

200 feet (61 m) with #22 AWG 6-wire cable

500 feet (153 m) with #18 AWG 6-wire cable

Unshielded wire is acceptable, however some host

controllers require tighter standards.

4. Reader options are selected by a rotary switch located on

the front of the reader circuit board.

5. With EMPI cards, the proper 8 or 16-bit "Comparison

Number" must be entered into memory of the host access

controller (similar to a site or facility code). These

numbers, as well as the "Job Code" number used when

reordering EMPI Cards, will be found printed on the label

of your EMPI Card carton. Details are found in the

Comparison Number Check Section.

 3110-6444 W/P P /T Reader, White

 3110-6445 W/P P /T Reader, Black

 3110-6446 W/P P /T W/heater bar Reader, White

 3110-6447 W/P P /T W/heater bar Reader, Black

 3110-6448 W/P P /T Connectorized Reader, White

 3110-6449 W/P P /T Connectorized Reader, Black

9292 Jeronimo Road

Irvine, CA 92618

Voice (800)-237-7769

Fax (949)-598-1690

email:

[email protected]

internet: www.HIDcorp.com

Mounting

1. Mount the reader either horizontally or vertically on:

 A single-gang handy box.

 A flat surface (wall, etc.) with or without the

adapter plate.

 On a structural door frame (mullion).

2. When mounting, consider the angle of the reader card slot

in relationship to the natural angle of the wrist when holding

the card. This usually means the card slot points away from

the door. As an example, if mounted on the right side of a

door the slot points right of away from the door. If mounted

on the left the card slot points left. On a horizontal

mounting, the card slot can point either up or down

dependent upon user convenience and height from the floor.

Typical mounting and recommended reader height from the

floor is shown in FIG 1.

55”

60”

Figure

3. The reader base plate determines which direction the

reader card slot will point. If the reader base plate is

mounted with its release latch down, the reader card slot

will point left. If mounted up, the reader slot points right.

1 2

Head Track Adjustment 2

Résumé du contenu

Page 1

Specifications INPUT; Magnetic Stripe Cards, high or low coercivity, EMPI I, EMPI II or ABA format. CARD SIZE: CR-80, 2.125" x 3.375" x .0

Page 2 - Head Track Adjustment

Comparison Number Check 1. When using the EMPI I or EMPI II encrypted card format, each user organization, or location is assigned a unique sequ

Commentaires sur ces manuels

Pas de commentaire

Hid Magnetic Stripe Reader 644 Installation Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Hid Magnetic Stripe Reader 644 Installation Guide. HID Magnetic Stripe Reader 644 Installation Guide User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Hid Magnetic Stripe Reader 644 Installation Guide