Hid EDGE EVO ELM Lock Module Installation Guide Manuel d'utilisateur télécharger pdf

Speciﬁcations

CONDITIONS

VOLTAGE DC

(VDC)

CURRENT

(Amp)

POWER

(W)

OPERATING

TEMPERTURE

CABLE LENGTH

REFERENCE

NUMBER

Input

DC Input (NSC)

+12 VDC 0.04 Amp 0.48

32° - 122°F

(0° - 50° C)

Lock Control Circuit

100 ft (30 m) = 22 AWG ● 0.65mm ● 0.33mm2

200 ft (60 m) = 18 AWG ● 1.02mm ● 0.82mm2

Hi-O CAN Bus Total Length 100 ft (30 m) -

22 AWG ● 0.65mm ● 0.33mm2

Maximum between drops 30 ft (10 m)

22 AWG ● 0.65mm ● 0.33mm2

ELMAxNN

X = K for Black

G for Gray

+24 VDC 0.04 Amp 0.96

DC Input (MAX)

+12 VDC 1.2 Amp 14.4

+24 VDC 1.2 Amp 28.8

Output

DC Output

(MAX)

AUX 12 VDC

Input @

Controller

Unregulated Jumpers +10 to +12 VDC 0.46 Amp* 5.52

AUX 24 VDC

Input @

Controller

Unregulated Jumpers +23 to +24 VDC 1.0 Amp* 24.0

Regulated Jumpers – 12 VDC +10 to +12 VDC 1.0 Amp* 12.0

PoE Input @

Controller

Unregulated Jumpers +16.5 to 24 VDC 0.30 Amp* 7.2

Regulated Jumpers – 12 VDC +10 to +12 VDC 0.60 Amp* 7.2

Output Power Selection

P103

1 & 2 2 & 3

12 VDC CAN / DC Input

Mounting

EDGE EVO

Lock ModuLe

ELM

InstallatIon GuIde

82301-901, Rev C.1

December 2012

15370 Barranca Parkway

Irvine, CA 92618-2215

USA

NSC = Normal Standby Condition

* Combined output rating not to exceed V*I = W

1.2 Amp (+24 VDC AUX Input, 28.8 W)

1.2 Amp (+12 VDC AUX Input, 12.96 W)

CAUTION: Some magnetic locks exhibit both high inrush current when activated and a high instantaneous

break voltage when de-energized due to magnetic eld collapse. It is recommended you use of a snubber circuit

across the controlling relay terminals to protect the controlling relay contacts. Go to support.hidglobal.com, see

Solution 891 - How do I wire a High In-Rush Current locking device to VertX/EDGE EVO. Not evaluated by UL.

This Hi-O interface module is wired to interface the EDGE EVO device

(Controller/Reader & Module or Networked) with electronic door components.

The Lock module provides outputs to an electronic locking device.

Install the EDGE EVO Lock Module within

a UL Listed single-gang electrical box or

optionally within a hollow metal door frame

(shown).

1 2

EDGE EVO 1
Regulatory 2

Résumé du contenu

Page 1 - EDGE EVO

SpeciﬁcationsCONDITIONSVOLTAGE DC (VDC)CURRENT (Amp)POWER (W)OPERATING TEMPERTURECABLE LENGTHUL REFERENCE NUMBERInputDC Input (NSC)+12 VDC 0.04 Amp 0.

Page 2 - Regulatory

RegulatoryULConnect only to a Listed Access Control / Burglary power-limited power supply, or Listed Access Control / Burglary PoE (Power-over-Etherne